How to Dehumidify a Car

If you left your car windows open during a rainstorm or forgot to take out your bathing suit after going to the pool, your car may need to be dehumidified. If your car is soaked, dry it out. You may be even able to prevent musty smells and mildew from forming! If you’ve already got a mold problem, clean out the mildew and take care of any lingering dampness. Then make sure you prevent mildew from invading your car ever again by checking for leaks and removing sources of dampness right away. Aussie Auto-glass,one of the best leading auto glass replacement company in Sydney, which is located at 813 princes highway in Tempe.

Method 1 Drying out Your Wet Car

1.Vacuum up lots of water with a wet/dry vac. If your car is soaked or if there’s a lot of standing water, you’ll want to start by getting that out. Use a wet/dry vac to remove the excess water.If you don’t have a wet/dry vac, you can rent one from a hardware retailer or an appliance rentals center. Aussie Auto-glass near you.

2.Remove floor mats and hang them in the sun. Take out all the carpets and put them in the sun to dry. Using the wet/dry vac, vacuum up any water that was hanging out under the mats. Leave the mats out overnight.

3.Use bath towels to absorb water on your seats. Put several thick towels on the upholstery. This should absorb most of the water. Check back in a few hours to switch out damp towels and replace them with new ones.

4.Leave the doors open and run fans overnight. If you can, leave all the doors open for at least 8-12 hours. Aim several large standing fans at the interior of the car. Focus especially on the seats. Let the fans run on their highest setting for at least 8 hours.

5.Use baking soda to absorb the remaining moisture. Baking soda can be used on all types of car interiors, including leather.If you managed to dry your car out quickly, you shouldn’t get any mold growth or musty smells. Just in case, sprinkle some baking soda all over the seats and mats. Leave this on for 24 hours, and then vacuum it up with the wet/dry vac.

Method 2 Cleaning Mildew out of Your Car

1.Park your car in a sunny spot. This will help dry out any dampness that’s causing mildew to form in your car. You’ll also want to dry out your mats in the sun.

2.Wear a protective mask and gloves while cleaning. Since you’re dealing with mold,wear a mask and latex gloves. After you’ve finished cleaning the car, thoroughly wash your hands and change your clothing.

3.Remove mats and check for dampness. Mildew often grows in storage areas or on the floors of your car. Check the spare tire compartment, then look under all the mats. Don’t forget the trunk. You should also see if your air conditioner is leaking by feeling for damp spots on the mat that sits underneath the filter.

4.Scrub off mold with a nylon brush. Once you’ve found your mold spots, tackle them with a nylon brush.You don’t need to use any soap or water, as this could actually make the mold problem worse.Just scrub at the mold until it’s removed from all the surfaces in your car. Then vacuum up all the broken-down mold particles.

.If the mold has left stains, use a carpet and upholstery stain remover. Follow the instructions on the bottle.

.If you’re cleaning leather, you may want to use a soft-bristled brush to avoid scratching it.

5.Spray the seats with white distilled vinegar. Fill a spray bottle with white distilled vinegar. Spray it on the seats and any affected mats or carpeting. This will kill the mold. Leave it on there to soak in for about 10 minutes.

.Vinegar can be used on leather and cloth interiors. If you’re concerned that it’ll damage your car, however, spot-test a small area of the interior by putting a little vinegar on it and letting it sit for 10 minutes.

6.Vacuum the entire car with a wet/dry vac. Go over the entire interior with the wet/dry vac. Vacuum up the vinegar and any remaining dampness. Pay special attention to the areas where you found mold.

7. Sprinkle an anti-mold solution on the surfaces of the car. Go to your local hardware store to find an anti-mold powder. Sprinkle it on the seats, carpeting, floors, and mats. This will kill off any remaining spores. Let it sit for about five minutes, then vacuum it up.

Method 3 Preventing Mildew and Mold Growth

1.Keep a container of baking soda in your car to absorb moisture. Fill a small container with baking soda. Check the container every few days and replace the baking soda when it gets damp.

2.Look for leaks throughout the car. Ask a buddy to sit inside your car while you spray it with a hose. They can see if any water leaks through windows, doors, sun and moon roofs, or even the floors. If you’ve got leaks, go to a repair shop to plug them up as soon as possible.

Aussie Auto-glass, With our highly trained team, we are able to provide you with professional windscreen replacement service and satisfied customer service.

3.Remove wet items from your car right away. Leaving wet clothes, towels, or even a cup of water in your car could cause the air inside the car to become damp. This might lead to the growth of mold and the return of that dreaded musty smell!

4.Clean your car every two weeks. Remove all trash. Wipe down the hard surfaces of the interior. Vacuum the mats and seats. Use upholstery cleaner to address any stains or dirt on the seats.