How to Change Your Windshield Wiper Blades & Arms

Are your wipers not keeping your windshield clear like they used to? When your windshield wiper blades or arms get dirty or damaged, it’s time to remove and replace them. Windshield wipers are some of the easiest repairs you can make, so it’s really easy to take them off and install new ones at home. We’ll walk you through how to change out wiper blades or arms so you can keep your windshield clean.Aussie Auto-glass(https://ozautoglass.com.au), one of the best leading auto glass replacement company in Sydney, which is located at 813 princes highway in Tempe.

Method1 Replacing Wiper Blades Only

1.Raise the windshield wipers. Hold onto where the wiper blade connects to the arm and slowly pull it up and away from your windshield. The wiper arm will stay in the position above your windshield without touching the glass.
•Place a towel on your windshield where the wiper blade would normally sit. That way, if you accidentally knock the arm down, it won’t damage your windshield.

2.Remove the wiper blade from the wiper arm. Each wiper blade has a connector where it attaches to the arm. There are 3 common connector designs, so how you change the blade on your vehicle varies depending on the type you have.
•Hook-slot connectors have a hook on the end of the arm that looks like the letter “J.” Find the tab where the blade connects to the arm, and either lift it up or push it in. Once released, push or pull the blade straight down toward the base of the wiper arm to remove it from the hook slot.
•Pin-type connectors have a small cylindrical pin at the end of the wiper arm that connects to the side of the blade. Lift the tab around the pin with a flathead screwdriver. Once you release the tab, just pull the blade straight off of the pin.
•Straight-end connectors have grooved ends that slide into the end of the wiper arm. Hold the tabs down on the sides of the wiper arm where it connects to the blade. Then, just pull the blade up and away from the wiper arm to remove it.

3.Install the new wiper blade. The way you install the blade depends on the type of connection the wiper arm uses. Make sure you choose a wiper blade that’s the same size as your old one, or else it may not fit on your windshield properly.
•Hook-slot connectors: Slide the new wiper blade into the hook slot at the end of the wiper arm, and secure the tab.
•Pin-type connectors: Slide the new wiper blade onto the pin. Once you have the blade in place, lock down the tab to secure it.
•Straight-end connectors: Slide the base of the wiper blade into the end of the wiper arm. If your design has a clip or tab, make sure that it snaps into place.

4.Test your wiper blades. Lower the wiper blade back against your windshield and turn on your vehicle. Spray water or windshield wiper cleaner onto your windshield and turn on the wipers. If they are wiping properly, then you’re finished with your repairs.
•If your wipers are still loose or wiggling on the arm, then check that they’re properly fastened before driving again.

Method2 Preparing to Change Windshield Wiper Arms

1.Check the wiper arm connection to see what kind you have. Look where your wiper arm connects to the body of your vehicle. There are 3 common kinds of wiper arms and they each fasten to the car differently.
.Bolt-on wipers are held onto your vehicle with a retaining nut mounted to a vertical post. The nut is usually covered with a circular plastic piece.
.Clip-on wipers have a small lever at the base that latches the arm to your vehicle.
.Spring-loaded wipers are held in place by a tension spring on the underside of the arm.

2.Buy an identical replacement wiper arm. Measure the wiper arm you just took off so you can buy one that’s exactly the same length and style. The wiper on the passenger side is usually longer than the one on the driver’s side arms, so ensure you have the correct length.
.Many auto parts stores have catalogs where you can look up the make and model of your vehicle to find wipers that are the correct size.

3.Gather your tools. You can remove most wiper arms with just a flathead screwdriver and a ratchet set, but stubborn wipers may need an arm puller. Keep all of your tools nearby and ready before you start taking the wiper arm off.

Things You Should Know

•Change the wiper blades by unlatching them from the end of the wiper arm and pulling them off.
•Remove a clip-on wiper arm by pulling the lever at the base of the wiper arm and lifting it off of your windshield.
•Take off a bolt-on wiper arm by unscrewing the retaining nut with a socket ratchet.

Aussie Auto-glass, With our highly trained team, we are able to provide you with professional windscreen replacement service and satisfied customer service.